Click the button below to add one #QC1212

Quad Core PMA with Fan&Pulley to your shopping cart

 

 

 

 

 

YOU ONLY PAY THE SHIPPING FEE ONCE PER ITEM #

SO ORDER AS MANY AS YOU LIKE FOR ONE SHIPPING FEE.

 

Please provide a "Street Address" for UPS shipping. NO P.O. Boxes Please!!

We offer FedXE or UPS GROUND SERVICE only to the USA and Canada.

All items are insured against loss and you will be Emailed a UPS tracking #

Again, absolutely NO Post Office shipments and also NO P.O. boxes please!!

For all international orders link here)

 

---

SUPER-CORE

The 'QUAD-CORE' is our highest amperage model in the Super Core series

Note: To hold 325 Amps you need to sustain 16,000 RPM requiring 25 to 30 hp depending on voltage demand.

Large 80MM pulley and fan comes with all QC12 models !

(Smaller pulley sizes will slip on this ultra powerful model)

Ohms law calculator

 

#SC SERIES PMA's -

Our PMA's include only the spacers, shaft nut and lock washer.

 

 

 

#QC1212 - Quad Core is our highest amperage model PMA!

Highly recommended for engine, hydro and belt driven applications!

 

 

325 amps! (16,000 rpm) - Includes cooling fan and 80MM pulley as stand equipment.

DO NOT REMOVE COOLING FAN! This model can get hot! VERY POWERFUL!!

Serpentine pulley system required loads over 4000 Watts See Power curves -

You can go from 12 to 90 volts just by changing the pulley ratio. For an engine or hydro driven system the QC12 it is the BEST choice since it is so powerful and versatile.

 

 

---

HEAT WARNINGS:

IF you are pulling over 500 Watts without a cooling fan your PMA it will over heat! Fan kits are very important to have on ALL high amp applications!!!!--- Keeping your PMA's cooled, fused and under reasonable loads is the operators full responsibility. Monitor your PMA for excessive heating in all experimental machinery! Maximum PMA's operating temperature is 350 F. for 100% duty cycle. No warrantees on ANY burned out PMA's! They are sold in good working condition and you have to keep them cool and never over loaded regarding amperage draw.

 

A PMA RUNNING SLOW WHILE DRAWING A FULL AMP LOAD IS A DEAD PMA!

Here is guide to help you choose the right PMA and keep it cool via the correct RPM V. AMPS coefficient

These figures must then be matched to the power curves. This total calculation must be done

correctly or you may find yourself burning up a few PMA's as part of your learning curve.

(Expensive lessons for the inexperienced!!!!!!!! All Sales Final)

 

POWER DRAW CHART

0 to 300 Watts - Required RPM for proper cooling fan operation = 0 to 300 rpm +

300 to 800 Watts - Required RPM for proper cooling fan operation = 1400 rpm +

800 to 1500 Watts - Required RPM for proper cooling fan operation = 2500 rpm +

1500 to 2500 Watts - Required RPM for proper cooling fan operation = 3700 rpm +

2500 to 5000 Watts - Required RPM for proper cooling fan operation = 5500 rpm +

5000 to 7000 Watts - Required RPM for proper cooling fan operation = 8500 rpm +

7000 to 10,000 Watts - Required RPM for proper cooling fan operation = 11,000 rpm +

10,000 to 14,000 Watts - Required RPM for proper cooling fan operation = 18,000 rpm +

14,000 to 16,000 Watts - Required RPM for proper cooling fan operation = 25,000 rpm +

 

 

 

 

 

 

 

 

http://www.youtube.com/watch?v=SchQ5nxo3So